Powder Type Vibrating Animal Material Instrument Equipment

• Customization: Available
• After-sales Service: Guarantee
• Warranty: Guarantee
• Model NO.: SQH-QT
• Working Temperature: Normal Atmospheric Temperature
• Working Pressure: Atmospheric Pressure
• Power Specifications: 3p 380V
• Air Supply Pressure: 0.4-0.8MPa
• Transport Package: Wooden Case/Wound Film
• Specification: Stainless steel/carbon steel
• Trademark: QH
• Origin: Changzhou, Jiangsu
• HS Code: 8401200000
• Production Capacity: 100 Sets/Year

Product Description

Product Overview

Material level gauge: material level measurement refers to the detection of the height of materials (solid or liquid level) in closed or open containers during industrial production; The instrument that completes this measurement task is called the level gauge. Material level meter is also called "material level meter", "material level meter", "material level meter" is also called "material level meter", "material level meter", "material level meter", "material level monitor", "material level monitor", etc.
Classification is also called "material level meter" and "material level meter"
Continuous material level meter: a material level meter that can realize real-time and continuous monitoring of the material level height of the silo.
Material level switch: the switch that controls the material level height of the silo through point measurement.
Spin resistant level switch - threaded type

Working principle

The working principle is to use the permanent magnet motor to drive the blade to rotate. When the tested material rises to the blade position, the blade rotation is blocked, and the resistance is transmitted
To the detection device in the junction box, the device will output a switch signal and cut off the power supply to stop the blade rotation. When the material level drops,
When the blade resistance disappears, the detection device will return to the original state depending on the tension of the spring, and adjust the spring tension according to the specific gravity of different materials
If it is large, adjust the spring tension to strong or strong, otherwise adjust it to weak or weak.

Installation precautions

1. The inlet of the junction box must be downward, and the cable fixing nut must be locked.
2. During power transmission, confirm that the power supply voltage is the same as the voltage marked on the rotary resistance switch.
3. The load of the controlled circuit must match the contact capacity of the rotary resistance switch.
4. The anti rotation switch shall not be installed under the blanking port to reduce material impact on the blade and misoperation; When unavoidable, it can be installed on the blade Install the protective plate.
5. When the shaft length adjustable rotary resistance switch is disassembled and installed on site, the lock nut must be coated with oxygen deficient glue when the wire rope joint is connected with the transmission shaft,Then use a wrench to lock it.
6. There shall be no toxic gas corrosive to aluminum alloy on the installation site.

Product technical parameters
 

Power supply	220VAC(A),110VAC(B),12VAC(C),24VDC,50/60Hz
Power consumption	3W
Contact capacity	5A/250VAC SPDT
Blade speed	Counterclockwise 1r.p.m. (rpm)
Moment	10kg·m (1.0N·m)
Material density	≥0.4g
Operating temperature	-10~80 ºC (the maximum temperature can reach 300 ºC)
Insulation impedance	≥100MΩ(500VDC)
Dielectric strength	1500V 1min

Product pictures

Product features

--It is characterized by vibration, economy and durable structure
--It can be used for any type of silo and hopper
--It can self clean, so it is also suitable for food grade or abrasive materials (granular or powdery materials)

Torque adjustment 

1. The user can adjust the torque according to the specific gravity of the measured material. When the specific gravity of the tested object is large, the spring torque can be adjusted to the strong or strongest position, and the sensitivity of the switch is poor at this time; When the specific gravity of the measured material is small, the tension spring can be adjusted to weak or weakest, and the switch sensitivity is good at this time.
2. Specific method: open the junction box, take out the end of the torsion spring close to the multi hole, and insert it into the corresponding hole as required (the hole close to the terminal block has the strongest torque).
Note: Do not replace the tension spring at will to avoid misoperation.

Common faults and troubleshooting
 

NO	Fault phenomenon	Cause analysis	Exclusion method
1	When the material reaches, the blade still rotates	Blade size is inconsistent with material specific gravity	Re size blade
2	Blade deformation or transmission shaft deformation and bending	Material impact force is too large	Add protective plate or take other protective measures above the blade
3	Blade does not rotate	1. The power supply is not connected properly 2. The motor is burnt	Check the line and connect the line Contact our company to replace the motor

Routine maintenance

1. Check whether the drive shaft and blades are bent, deformed, damaged or loose.
2. Check whether the connection between drive shaft and blade is firm.
3. Regularly remove materials and sundries on the blade and drive shaft.

Company profile
 
QIANGHAN MACHINERY (CHANGZHOU) CO.,LTD is committed to the design and manufacture of powder unpacking and unloading, conveying and loading, powder valve equipment and related supporting equipment and products are widely used in chemical, food, medicine, feed, cosmetics and other industries. 
Strong drought has professional technical personnel and a quality work team, which can timely provide customers with perfect after-sales service. Survive with quality, develop with service, always adhere to the principle of contract and trustworthiness. Our products excellent in quality and affordable in price. Welcome new and old customers to the factory!

FAQ

Q:What is the delivery time ?  
A:Our delivery time is within 3-7days after we get your payment; For large qty mass order, the time should be confrimed by quantity.
   
Q: How about the Warranty time ?  
A:Our warranty time is 12 months after you get our goods. All products are provided with lifelong technical services and support.

Q:How about the payment terms ?  
A:You can choose T/T, Western union or Paypal.

Q: Do you provide samples ?  
A: Yes, we have materials in stock to help you to get the samples as soon as we can.  

Q:Can I have my own logo of the products?  
A:Of course. We provide OEM services such as product's material, dimension, color, etc.